- Manuals
- Brands
- Travel Vision Manuals
- Car Navigation system
- Q7
- Installation and user manual
Hide thumbs
1
2
3
Table Of Contents 4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
-
- Contents
- Table of Contents
- Bookmarks
Table of Contents
-
Table of Contents
-
TRAVEL VISION Q7 (Duo)
-
Travel Vision Q7 (Duo) Package
-
Parts Checklist
-
Installation Instructions
-
Determining Installation Position
-
Installing Satellite Dome and Control Unit
-
Electrical Connection Satellite Dome
-
Electrical Connection Control Panel (MCM Unit)
-
Assembling and Disassembling of the Dome
-
Function Control Panel MCM Unit
-
Use of the MCM Unit
-
View Status MCM Unit
-
View Error Codes MCM Unit
-
Explanation of Error Codes
-
Menu Structure
-
Menu Settings
-
Choice of Satellite Together with Travel Vision Q7 Duo
-
Choice of Satellite Together with Travel Vision Q7
-
Standby
-
Menu Installation
-
Firmware Update
-
Technical Details
-
IP 55 Protection Certificate
-
Warranty Conditions
-
Installers Manual
-
Installer's Menu MCM Unit
-
Choice of Satellite Together with Travel Vision Q7 Duo
-
Choice of Satellite Together with Travel Vision Q7
-
End Switch in Satellite
Advertisem*nt
Quick Links
Download this manual
information: www.travel-vision.com
INSTALLATION and USER MANUAL
TRAVEL VISION Q7 and Q7 Duo
Version 2.3 November 2019
Table ofContents
Advertisem*nt
Table of Contents
Summary of Contents for Travel Vision Q7
- Page 1 INSTALLATION and USER MANUAL TRAVEL VISION Q7 and Q7 Duo Version 2.3 November 2019...
- Page 2 Travel Vision ® is a registered trademark by Travelvision B.V. Please read this installation and user manual before putting your Travel Vision Q7 (Duo) into service. Follow the instructions and take all warnings, included in this installation and user manual to heart.
- Page 3 You can clean the dome by use of a soft damp cloth with a soap solution. The dome is IP 55 and not suitable to be cleaned by means of a powerful waterjet/deck washing hose. If the dome is required to be tilted for the purpose of the distance between the water line and the highest fixed part of the ship (such as for low-profile coasters), then please consult your dealer/installer concerning wiring, supply voltage and other measures.
-
Page 4: Table Of Contents
View Error Codes MCM unit …………………………16 Explanation of Error Codes …………………………16 Menu structure …………………………18 Menu settings …………………………19 4.3.1 Choice of Satellite together with Travel Vision Q7 Duo …………19 ……………….. 4.3.2 Choice of Satellite together with Travel Vision Q7 …………………………20 Standby …………………………20 Menu Installation …………………………21... -
Page 5: Travel Vision Q7 (Duo) Package
Travel Vision Q7 (Duo) package The Travel Vision Q7 (Duo) is packed in a strong plastic bag, in a 80x80x91 cm cardboard box. Using the strong plastic bag, the device can easily be lifted out of the box by 2 people. -
Page 6: Installation Instructions
Installation instructions Determining installation position Choosing the installation location of the satellite dome When choosing an adequate location for the installation of the satellite dome, several factors, as summarised below, must be taken into account: • The ideal location is a location that has a clear view in all directions. •... -
Page 7: Determining Installation Position
Determining the position to install the control unit While choosing the position of the control unit, instructions below are to be followed: • The control unit can be installed in either an exposed or a concealed location. • With regard to possible following software updates, we do recommended that the control unit be installed in an accessible location. - Page 8 In case the Travel Vision Q7 (Duo) cannot be mounted from the underside with the included M8 bolts and lock rings, it is possible to fix the actuation from the inner side. Using sufficiently long M8 Inox bolts, you can secure the system from the inner side.
-
Page 9: Electrical Connection Satellite Dome
Measurements control unit (MCM unit) Electrical connection satellite dome The Travel Vision Q7 (Duo) must be connected to 24 Volt DC, in which case the current consumption is approximately 3 Amperes. The (brief) inrush current is significantly higher and also dependent on the power supply used and the power cord installed. - Page 10 • After the installation is completed, the satellite base should be covered using the dome. The Travel Vision Q7 is suitable for connection to 4 receivers as a standard. Diagram with connection of 4 tuners and optional switch box pagina 10...
- Page 11 The Travel Vision Q7 Duo is suitable for connection to 3 receivers as a standard, with unlimited reception of channels on Astra 1 (19’2) and Astra 3 (23’5) at the same time. A possible 4 receiver can be connected, however limited to only the reception of Astra 1 (19’2).
-
Page 12: Electrical Connection Control Panel (Mcm Unit)
Electrical connection control panel (MCM unit) The MCM unit should be connected as follows: Back of MCM unit. Diagram satellite to MCM 1. 5-pole connector 2. 2-pole connector is not being used 3. RS 232 NMEA input and output • Connect the 5-pole connector as indicated in diagram •... -
Page 13: Assembling And Disassembling Of The Dome
Assembling and disassembling of the dome The dome is attached by use of 3 M6 bolts. These bolts can be screwed and unscrewed completely. PLEASE NOTE! Special attention should be paid to this taking place under dry weather conditions. page 13... -
Page 14: Function Control Panel Mcm Unit
Function control panel MCM unit The MCM unit has 3 functions: 1 Monitoring; Being able to see the status of the satellite dish on the display. In this case multiple reporting codes may be displayed (see view Error Codes and Status). 2 Control: Giving instructions to the satellite dish at a distance for example choice of satellite, Standby function etc. -
Page 15: Use Of The Mcm Unit
This may take approximately 1 minute. After this start-up phase, the system will start searching for the configured satellite. After some time the Travel Vision Q7 (Duo) will be locked to the satellite and your TV set will show the image on the receiver. -
Page 16: View Status Mcm Unit
View Status MCM unit The display shows the status of the satellite to be followed. All status notification shown are notifications from the dome to the MCM unit. Status: Searching Limit : the system is looking for its points of reference Searching/scanning Sat : the system is looking for the satellite... - Page 17 No tuner settings can be recognised, repeat the software update procedure or check the cable and connections of the control unit. : Not possible DiSEqC active (not possible with Travelvision Q7 Duo) It is not possible to manually select a different satellite because auto DiSEqC is enabled via the main tuner.
-
Page 18: Menu Structure
Menu structure Different settings are possible in the menu of the Travel Vision Q7 (DUO). pagina 18... -
Page 19: Menu Settings
Restart satellite The satellite will restart itself (Press the enter key to restart satellite) 4.3.1 Choice of Satellite together with Travel Vision Q7 Duo (please note: ONLY Duo)! Press the up and down keys for scrolling through the satellite favourites list. -
Page 20: Choice Of Satellite Together With Travel Vision Q7
4.3.2 Choice of Satellite together with Travel Vision Q7. Press the up and down keys for scrolling through the satellite favourites list. Press the enter key to select satellite. NOTE! The satellites can be selected for the favourites list through the installer’s menu. -
Page 21: Menu Installation
Menu Installation Press the enter key and escape key for 5 seconds to go to the selection menu Firmware update Setting for updating your Travel Vision satellite with new software (press the enter key for selection) Place the USB-stick with the latest software version Press the Enter key, the system will read the software. -
Page 22: Firmware Update
: Software for the tuner print. Eeprom.bin : File for track settings of the system. For a firmware update you first go to the installation menu in the Travel Vision using the MCM control panel. Press the control panel, enter and escape at the same time for 5 seconds. - Page 23 The updating of the software is about to start. First the outdoor motor print will be provided with new software. Updating Outdoor: [ XXXXX-------- ] After completion of the 1 update the following notification will be shown in the display: Updated: Subsequently the tuner print will be provided with new software.
- Page 24 Updated: After this 4 update notification the entire Travel Vision system is provided with new Firmware and the system will start up once again. Please note!! Do not remove the USB disk until the system has completely started up again.
-
Page 25: Technical Details
Technical details Dish diameter 65 cm Diameter dome 78 cm Height dome 86 cm Weight 22 kg Dispatch volume and weight lxwxh=80x80x91 cm, Gross weight approx. 30 kg Power supply 24V DC Energy consumption 3/5 Amp. Max. Cabling MCM cable 4x0.32 mm2 shielded Supply cable 2x1 mm2 (minimal) -
Page 26: Ip 55 Protection Certificate
IP 55 protection certificate Travelvision BV, declares that the product Travelvision Q7 (Duo) complies with the mechanical directive IEC 60529 for a IP55 protection level. Werkendam, Nederland 18 September 2015 C.I. Visser Product Manager pagina 26... -
Page 27: Warranty Conditions
Vision system at the latest to Travelvision B.V., by the dealer. As proof of this registration, for both Travelvision B.V. and the owner of the Travel Vision system, the dealer is required to fill in, sign and send the included warranty certificate. -
Page 28: Installers Manual
TRAVEL VISION Q7 (Duo) Version 2.1 November 2019 Table of contents Installer’s menu MCM unit Choice of Satellite together with Travel Vision Q7 Duo Choice of Satellite together with Travel Vision Q7 End switch in satellite Travelvision BV Ir Lelystraat 10 4251 LS Werkendam Tel. -
Page 29: Installer's Menu Mcm Unit
Select the Travelvision type for the proper functioning of the electronics. You can choose from: 1. Travelvision Q7 2. Travelvision Q7 Duo (Press the up and down keys for scrolling through the selection list. Press the Enter key for selection.) -
Page 30: Choice Of Satellite Together With Travel Vision Q7 Duo
2. Choice of Satellite together with Travel Vision Q7 Duo Setting satellites for favourites list Select the satellites from the satellites list to go to the favourites list. The favourites list is a shortlist for the user. Standard setting in favourites list:... -
Page 31: Choice Of Satellite Together With Travel Vision Q7
Choice of Satellite together with Travel Vision Q7 Setting satellites for favourites list Select the satellites from the satellites list to go to the favourites list. The favourites list is a shortlist for the user. Standard setting in favourites list:... -
Page 32: End Switch In Satellite
3. End switch in satellite It is important that the setting of the end switch is not changed during the installation. Should this occur anyway and you cannot remember the initial position, you should set the switch in the original position. Turn the satellite until the switch is at the end-position in such a way that the cable harness is no longer twisted. - Page 33 Travelvision BV Ir Lelystraat 10 4251 LS Werkendam Tel. +31 (0) 183-505570 Fax + 31 (0) 183-505567 Web: www.travel-vision.com © Copyright 2019 Travelvision b.v. page 33...
This manual is also suitable for:
Q7 duo
